The Macard Wi-Fi Range Extender is an easy solution to solve a bad network by extending the range of your existing network without requiring new cables or difficult settings.

So, if you recently acquired a Macard device and want to get it set up quickly and correctly, this article is for you. We will go over each stage of the setup process in a manner that anybody can comprehend, even if they don't know much about computers. It's simple to set up and works quickly if you do it right. You may increase the signal in the garage, upstairs, or just in that final area of the lobby.

We'll go over everything step by step so that you can effortlessly setup Macard WiFi range extender and go back to using the internet whenever and whenever you want.

Why do you need a range extender?

Routers are excellent, but walls, distance, and outdated wiring might make your signal weak. A range extender works like a middleman by picking up your router's signal and sending it out further. It's not a substitute; it's the greatest buddy of your signal in dead zones.

What You'll Need

• A functional Wi-Fi router

• The SSID and password for your primary network

• A phone or laptop

• A wall socket, ideally one close to your router at first

All right, let's get started.

Step 1: Plug in your extender near the router
First, connect your Macard extender to a power source near your router. Wait until the power LED stays on. It’ll take around 30-60 seconds. Do not rush during this step.

If you see the light flickering for longer duration, plug the device in a different outlet, maybe the outlet is at fault and not the device.
Step 2: Connect to the Macard Network
Look for a network name similar to "Macard_Ext" in your Wi-Fi network list. Connect your device to that SSID. If your device is not receiving internet signals, it’s absolutely fine for now. This is the point, where you are configuring your network.

Step 3: Click on the Configuration Page
Open a web browser and put 192.168.10.1 into the address bar. You will reach the page where you may set up your Macard. The default login is generally admin/admin. Push the pinhole button on the back for around 10 seconds to reset it if you've played with it previously and forgot.

Step 4: Pick Repeater Mode
Once you're signed in, choose Repeater Mode. This is how you setup macard Wifi range extender to your primary Wi Fi. It will display you a list of networks. Choose your home network: 2.4 GHz or 5 GHz. Yes, you may do both, although it depends on the model of your Macard.

Type in your router's password exactly as it is, including symbols, capital letters, and everything else. Press "Apply" or "Connect."

Step 5: Restart the device

It will take a minute for the extender to resume. The light that spins signals it's synchronizing. The signal LED should either flash steadily or pulse slowly when it settles (this varies on the type).

Step 6: Get It to the Sweet Spot

After disconnecting it, place it halfway between your router and the weak Wi-Fi region. Plug in the device and let the light cease flickering. Putting the device too far from the router will prevent the extender from obtaining adequate signals.

Additional Quick fixes

1. Don't use thick walls or metal equipment like fridges and washers; they impede signals more than you believe.

2. If you can, use dual band. 5 GHz is quicker but has a lower range, whereas 2.4 GHz goes further. Choose depending on where it goes.

3. After setting up, change the default admin password. The default "admin/admin" is simply begging for problems.

4. Every now and then, update the firmware. Check for updates on the Macard website or the setup page. This will make your system more stable and secure.

What If Setup Doesn't Work?

• Can't see Macard_Ext SSID in your device? Plug in the router in a different power outlet.

• The extender doesn't display your router in the list? Check to see whether your router is sending out a 2.4 GHz signal. whether it is, try restarting both the router and the extender.

• Is the password wrong? You will know. Just reset the extender and try again. Next time, keep that password sheet close by.

Final Thoughts
We setup macard Wifi range extender jointly by plugging it in, clicking on a few buttons, then moving it upstairs to the landing. Boom—full bars, nice video, and no problems.

From now on, setting up your Macard Wi-Fi range extender won't be a hassle if you follow these simple steps:

1. Plug it in close to the router

2. Link to Macard_Ext

3. Choose your network in repeater mode and type in your password.

4. Let it start again.

5. Put it between the router and the weak zone.

Follow the given steps to receive ample signals in the WiFi dead zones and keep your internet working effortlessly.

FAQs

1. Is it possible to use the extender without connecting it to the router?
No, it will not transmit any signals until it is connected to your network in repeater mode.

2. What is the ideal area to place the extender while setting it up?
Ideally, place the device midway between the router and area with minimal to normal. Move the device closer to the router if it is showing the amber or magenta light.

3. Is it safe to leave it plugged in all the time?
Definitely. Macard extenders are made to work all the time. Just don't put it behind items that trap heat.