Match Fall Protection Roof Anchor Points to the Roof

Installing the wrong anchor for the roof type is a common mistake, since a tin roof and a tile roof each need a different weather seal to stay watertight around the penetration. Fall protection roof anchor points matched to the specific roof material avoid this, and Roof Extenda manufactures three distinct variants covering the most common roof types across Australia. Each anchor is a single-person fall arrest system rated to 1500 kilogram-force and compliant with AS/NZS 5532:2013, bolted directly to the timber rafter for maximum structural integrity.

Contact Roof Extenda to find the right fall protection anchor for your roof type.
Read More: https://www.roofextenda.com.au..../product-category/ro

Fit Carport Support Brackets with the Right Hardware

A carport that looks well-built on the surface can still fail early if the fixing hardware underneath isn't up to the job, particularly on sites exposed to coastal air or high wind loads. Cutting corners on bolts and screws is rarely visible until the structure starts to move.

Carport support brackets installed with the correct hardware avoid this problem from the outset. Roof Extenda's brackets fix to the rafter and wall top plate using hex bolts and screws rather than lighter fixings, giving the structure a genuinely load-bearing connection suited to taller carports built for 4WDs, boats or caravans. Mild steel and 316 marine grade stainless steel options are available depending on how exposed the site is to corrosion.

Fixed with hex bolts and screws for a load-bearing hold
Mild steel or 316 marine grade stainless steel options
Suited to taller carports for 4WDs, boats and caravans
Weather seal included with every bracket kit

A carport is only as reliable as the hardware holding it up. Contact Roof Extenda to discuss carport roof brackets suited to your build.
Read More: https://www.roofextenda.com.au..../product-category/ca

Get a Clean, Compliant Fixing for Carport Brackets

Fixing a carport frame straight into an existing fascia might look fine on install day, but fascia boards flex and weather over time in ways that eventually show up as movement in the new structure. Carport support brackets fixed to a genuine structural point avoid that problem from the outset.

Roof Extenda manufactures brackets that bolt directly to the rafter and wall top plate using hex bolts and screws, giving carport frames a fixing method built for the long term rather than one that relies on a non-structural board. Suited to both tile and metal roofs, each bracket kit includes a weather seal for a finished, weatherproof result.

Fixes to the rafter and wall top plate, not the fascia
Suited to tile and metal roof types
Weather seal included with every bracket kit
Available in mild steel and 316 marine grade stainless steel
A carport is only as solid as what it's bolted to, and Roof Extenda's brackets are built with that in mind.

Contact Roof Extenda to find the right carport support brackets for your build.
More Info: https://www.roofextenda.com.au..../product-category/ca

Keep Roof Access Compliant with Fixed Anchor Points

Booking a contractor for roof work without confirming anchor points are in place can leave a job stalled before it even starts, especially when temporary tie-off equipment needs to be arranged separately. Fall protection roof anchor points installed permanently remove that delay, giving any trade a fixed, compliant connection point ready to use. Roof Extenda designs and manufactures these anchors in Australia, bolting directly to the rafter for a secure single-point attachment suited to cleaning, maintenance and inspection work.

Contact Roof Extenda to fit compliant anchor points to your roof.
More Info: https://www.roofextenda.com.au..../product-category/ro

Raise Your Pergola Roofline with Riser Brackets

A pergola built too close to the existing fascia can limit airflow underneath, leaving the space warmer and less comfortable during summer. Pergola riser brackets address this by lifting the new roofline above the gutter, allowing better ventilation while keeping the structure fixed to the rafter and wall top plate rather than the fascia. Roof Extenda designs and manufactures roof brackets for pergola projects using hex bolts and screws for a structurally sound fixing method, built to suit high-wind conditions across Australia. Get in touch with Roof Extenda to find the right riser brackets for your pergola.
More Information: https://www.roofextenda.com.au..../product-category/pe